  |
        |
Installation instructions for: ORIGINAL collection , Ogura Elite, Ogura Plush and Ogura Pure, Cameo
CAMEO
PANEL
WALLPAPER INSTALLATION INSTRUCTIONS
STRAIGHT
MATCH
ΠWalls
should be clean and properly
primed with a quality wall covering primer.
� Use
a clear heavy duty strippable wall
covering adhesive. Apply
paste evenly to
back of paper with paint roller.
Let
paper relax for 1-3 minutes before applying.
Ž
Use a
smoothing brush to smooth out the
material.
� When
hanging this paper, do not use a seam roller. For
this will crush the material.
Wipe
off excess paste immediately with a
damp sponge. Don’t scrub or rub.
If
you need to splice two pieces
together, overlap and double cut (follow the contour of the pattern
when double
cutting.)
If
you have any questions, please call
Professional
Installation is Recommended!
OGURA
PLUSH AND PURE
PANEL
WALLPAPER INSTALLATION INSTRUCTIONS
CAN
BE HUNG HORIZONTALLY OR VERTICALLY
(HORIZONTAL
PREFERRED)
Walls
should be clean and properly
primed with a quality wall
covering
primer.
Use
a clear heavy duty strippable wall
covering adhesive. Apply
paste evenly to
back of paper with
paint roller. Let
paper relax for 1-3 minutes before applying.
Each panel should be DOUBLE-CUT on
both sides, top and
bottom.
Panels
should be trimmed to a maximum of 30” x42” (trim
approx. ½ “ from
edges of fiber pattern on
all sides).
Wipe
off excess paste immediately with
a soft damp cloth. Don’t scrub or rub.
If
you have any questions, please call
Professional
Installation is
Recommended!
OGURA
ELITE
PANEL
WALLPAPER INSTALLATION INSTRUCTIONS
CAN
BE HUNG HORIZONTALLY OR VERTICAL
(HORIZONTAL
PREFERRED)
Walls
should be clean and properly
primed with a quality wall covering primer.
Use
a clear heavy duty strippable wall
covering adhesive. Apply
paste evenly to
back of paper with paint roller. Let paper relax for 1-3 minutes before
applying.
Each panel should be DOUBLE-CUT on
both sides, top and
bottom.
Panels
should be trimmed to a maximum of
24” x35” (trim approx. ½
“ on each
long side & 1“
on each short side from
edges of fiber pattern ).
If
you have any questions, please call
Professional
Installation is
Recommended!
PANEL
WALLPAPER INSTALLATION INSTRUCTIONS
Walls
should be clean and properly
primed with a quality wall
covering
primer.
Use
a clear heavy duty strippable wall
covering adhesive. Apply
paste evenly to
back of paper with
paint roller. Let
paper relax for 5 minutes before applying.
Each panel should overlap to accommodate at
least a 1”
DOUBLE-CUT on
both sides, top and bottom.
Wipe off excess paste immediately with a soft damp cloth. Don’t scrub or rub.
If
you have any questions, please call
|
|
TORN
INSTALLATION INSTRUCTIONS
|
||||
|
|
Wallcovering
is shipped in pre-torn pieces approx. 2’x 2’ (a.k.a
Middles)
|
||||
| Step 1: Cut
straights. Using a metal straight edge and blade, cut appropriate number of Middles in half (alternating directions), for area to be papered. (Paper may be torn into smaller pieces by ripping away from you to avoid unpainted edges) |
 |
||||
| Step
2: Glue |
  |
 |
|||
| Lay a pile of pieces on work
surface (approx. 50 or more). Roll on heavy duty clear strippable glue evenly making sure edges are fully covered. (the proper amount has no oozing of glue from edges when paper is squeegeed on wall) Glue and book 10-20 pieces depending on application speed |
|||||
| Step 3: Install |   |
 |
|||
| Apply straights on all edges
using a squeegee and wet rag or sponge. Continue with same as above with middles. To avoid a pattern apply in various directions. |
|||||
| Step 4: Done! |   |
||||
AVIGNON
WALLCOVERINGS on Facebook 
3941 E. CHANDLER BLVD.--SUITE 106-122---PHOENIX--ARIZONA--85048 | TOLL FREE: 877.800.2278 | T: 480.759.0504 | F: 480.759.3624